A.The input power supply is three-phase 380V50HZ. The voltage waveform is sinusoidal, and the amplitude fluctuation is not greater than+5~- 10%. The frequency fluctuation shall not be greater than 2HZ, and each phase shall be symmetrical. There are no higher harmonics in the power grid that are sufficient to damage the frequency converter. B. Temperature: 0~40 ℃ C.Humidity: The relative humidity shall not exceed 85% (20 ℃±5 ℃),D. Altitude: less than 1000 meters E. No severe vibration and impact
LZ600 wire drawing machine
1. 1 Professional and technical personnel are required to carry out installation and commissioning. Before use, it is necessary to carefully read this manual and the relevant electrical instructions provided.
1. 2 Each machine and electric control cabinet shall be reliably grounded with a grounding resistance not more than 4Ω.
1. 3 There should be no accumulated water on the table top, especially near the operation box, as it can easily lead to circuit failure due to water infiltration.
1.4 It is prohibited for multiple people to operate the same equipment at the same time to avoid accidents.
1. 5 The electric control cabinet should be placed in a clean and dry room, and the door should be closed when working to prevent dust intrusion from causing device performance degradation or failure. Air conditioning is used to maintain the ambient temperature of the electric control cabinet. Frequently check the operation of the cooling fan on the top of the electric control cabinet.
1. 6 Before starting the machine, check whether the safety device is normal.
1. 7 Do not operate the components in the electrical cabinet with power. After cutting off the main power supply, wait at least five minutes, and wait until the intermediate circuit capacitance is discharged before operating the frequency converter, motor, or motor cable.
1.8 Do not touch the IC circuits on the inverter control interface board and motor control board, as static electricity may damage these circuits.
1.9 Please provide the power supply and operating environment according to the technical requirements of Section 3.2. It is not allowed to arbitrarily change the parameters of the frequency converter and PLC. The user shall be responsible for any damage to electrical components caused by human factors.
The second Delivery inspection
2. 1. Check whether the equipment is damaged and complete upon delivery (according to the packing list). If there is any damage or inconsistency with the contract, please contact the dealer or manufacturer immediately.
2. 2 The manufacturer is only responsible for quality issues arising during production, and is not responsible for damage caused during unpacking, improper installation and use, or damage caused by overload operation.
2. 3 After unpacking, the accompanying documents should be properly kept, as they are necessary during equipment installation, commissioning, and use.
bobbin spooler machine coiler machine Jiangyin Wanyi Machinery CO.,Ltd , https://www.wydrawmachine.com
A pellet mill, also known as a pellet press, is a type of mill or machine press used to create pellets from powdered material.
In the ring die pellet mill, there are radial slot throughout the die. Powder is fed into the inside of the die and spreaders evenly distribute the powder. Two rollers then compress the powder through the die holes. Two cutters are used to cut the pellets free from the outside of the die. Pellet mill used to produce animal feed, wood pellets, and fuel pellets for use in a pellet stove. Ring die pellet mill generate less wear and tear during pelleting, and work more energy efficient, which is widely adopted in commercial and large scale production lines.
Animal Aqua Feed Machinery Specification:
(1)This series pellet mill suitable for making all kinds of animal feedstuff. Which capacity 1000-200000 kg for feed factory .
(2)The machines can be match different size of ring die hole size , such as φ1.0,φ1.2,φ1.5,φ2.0,φ2.5,φ3.0,φ3.5,φ4.0,φ4.5,φ5.0,φ6.0,φ8.0 , always for making shrimp, fish feed to use for φ1.0--3.5 ring die ; chicken feed for φ3.0; Swine feed for φ3.0--4.5; Cattle, horse for φ6.0--8.0).
(3)The machine adopt imported SKF or NSK bearings, the motor brand is Siemens or china famous Wannan brand .
Driven by gear .more strong than by belt, and the capacity 10% higher than by belt .
(4)The machine also matched the safty equipment , once overload , the safty pin will crack, to protecting the machine lifetime
ModelMain motor power(KW)
Capacity
(t/h)Feeder power(KW)
Conditioner
Power(KW)Ring die diameter(mm)
Pellet size(mm)
XT-320A
37
0.5-0.7
1.5
2.2
320
1-10
XT-350A
45-55
0.8-1.2
1.5
3
350
1-10
XT-420A
90
2.0-5.0
2.2
5.5
420
2-12
XT-480A
90
3.0-8.0
2.2
5.5
480
2-12
XT-508A
110
3.0-10.0
2.2
5.5
508
2-12
XT-572A
160
5.0-12.0
2.2
5.5
572
3-12
XT-678A
185
7.0-12.0
3
11
678
3-12
XT-768A
250
7.0-15.0
4
18.5
768
3-12
Before you purchase the whole line, you have to inform us the basic information as below:
1. What is the type of your raw material? And what is the size?
2. Raw material moisture content? You can use moisture meter to evaluate it.
3. What is your expectation on the whole line output?
We Promise: All the pellet machine from Xing tai Machinery will enjoy two years quality warranty period.
XT Machinery, Works For You.