The liquid turbine flow meter adopts a new intelligent design and can maintain high-precision measurement when used. When used, the turbine flowmeter has superior performance and long service life, and it has strong anti-interference ability. When it is used, the turbine flowmeter may encounter various electromagnetic interferences if the flowmeter resists interference. The capacity is not good enough, which may affect the measurement accuracy of the flow meter when it is used. Spring Pin,Spring Loaded Pin,Spring Pin Latch,Spring Loaded Locking Pin Zhejiang Kahuan Technology Co., Ltd. , https://www.zjkhtech.com
Because the turbine flowmeter is sensitive to the conditions in the field, the user should meet its ideal requirements under the conditions of maximum satisfaction, so as to maintain the accuracy of the factory meter and obtain the ideal measurement data. When the temperature and pressure of the fluid medium differ greatly from the reference conditions, the volume change of the sensor housing can be calculated based on the material of the sensor and the temperature pressure, and the meter reading can be corrected. When the viscosity of the fluid medium under working conditions is different from that of the calibration fluid, the parameters of the viscosity correction curve provided on the installation and operating instructions should be corrected.
Turbine flowmeters have certain requirements on the lengths of the straight sections upstream and downstream during measurement, and they should be managed according to the installation requirements, especially when the user requires high precision. The meter shows the volumetric flow under the working conditions of the media. To know the standard volume flow or mass flow, density compensation is also required.
The accuracy of the liquid turbine flow meter is determined under reference conditions ( or standard operating conditions ) . For turbine flow meters, the reference conditions generally include: ambient conditions ( ambient temperature 15 °C to 35 °C, relative humidity 45% ~ 75% , atmospheric pressure 86kPa, ~ 108kPa, no electric field, magnetic field interference, no vibration ) ; power source conditions (220V ± 10% or 110V, 50HZ ± 1 , or 24VDC) ; fluid conditions ( when using fluid calibration, calibration The pipeline is an industrial circular tube, single-phase Newtonian fluid, fully developed and fully developed turbulent velocity axis-symmetrical distribution, no vortex, non-disturbance, steady flow.The calibration fluid is usually water, oil, air, according to need. a downstream turbine flowmeter sufficiently long straight pipe fluid temperature is generally room temperature, fluid pressure is generally less 0.25MPa). Obviously, the actual working conditions of the turbine flowmeter are usually different from the reference conditions, which can cause changes in the accuracy of the turbine flowmeter.
The accuracy of the liquid turbine flow meter during use may be reduced due to the following reasons:
1. The fibrous or viscous impurities in the fluid are attached to the rotating part of the flowmeter, which increases the rotational resistance, causing the indicator value of the instrument to decrease, causing a negative error and adversely affecting the fluid supplier.
2. The change of fluid temperature and pressure may cause the air contained in the pipeline to escape, or the pressure in the pipeline is lower than the saturated vapor pressure of the fluid, so that part of the liquid becomes steam, or it may be caused by the negative pressure of the medium. The gas is sucked into the pipeline. These gases flow along with the measured fluid, causing the indicator value of the instrument to increase, causing a positive error, which is detrimental to the demand of the fluid.
3 , the media generally have some impurities, wear on the bearings, shafts, so that the gap between the two increases, the dynamic balance of the moving parts is destroyed, the speed is reduced, or dirt into the gap, so that increased resistance to movement , Speed ​​drops. All of these reasons cause the display value of the instrument to decrease, causing a negative error, which is detrimental to the fluid supplier.
4. The bad working environment will also have a great impact on the measurement results, such as electromagnetic field interference, dust, high temperature, vibration, and humidity, which may cause malfunction or failure of the turbine flow sensor, directly causing the indication error of the turbine flowmeter. Errors may be positive or negative, may be insignificant, or may completely fail. For the above phenomenon, when it is more serious, problems can be found in the comparison of process working status and it is easy to take corresponding measures. However, in the early stages of the problem, problems could not be discovered without special measures. 
