Explosion-proof equipment definition: Electrical equipment that does not cause the surrounding explosive atmosphere to ignite under specified conditions.
Divided into two categories
Category I: Coal mine underground electrical equipment;
Category II: Electrical equipment for all other explosive atmospheres except coal mines and downholes.
Class II can be further divided into Classes IIA, IIB, and IIC. Devices that mark IIB can be applied to the conditions of use of IIA equipment; IIC can be applied to the conditions of use of IIA and IIB.
Note: The IIC mark is a higher explosion-proof rating, but it does not mean that the device performs best.
Maximum surface temperature: The maximum temperature reached by any component of an electrical device that may cause ignition of the surrounding explosive atmosphere when the electrical device is operating under the most unfavourable operating conditions within the specified range. The maximum surface temperature should be lower than the flammable temperature.
For example, the ignition temperature of an explosive gas in an explosion-proof sensor environment is 100°C, then the highest surface temperature of any part of the sensor under the worst working conditions should be less than 100°C.
13 Meter Aerial Work Platform
Folding high-altitude work vehicles have been in the market for nearly 20 years. Due to their pure mechanical operation, they are simple, sturdy, and durable. This type of high-altitude work vehicle can also be called a curved arm high-altitude lifting vehicle, which is used for outdoor wiring and street light installation and maintenance. The working height is usually between 13 meters and 22 meters. The large arm can rotate 360 degrees, the hanging basket can rotate 180 degrees, and there is a set of manual operating rods at the turntable and in the basket, Used to control the upward, downward, and rotational movements of the boom, one person can also use this vehicle for high-altitude operations.
The blue brand aerial work vehicle produced by our factory adopts a hydraulic 360 degree full rotation, three folding arms, a single hydraulic lifting cylinder, with a two-way balance valve, an electrically controlled lifting arm, and an adjustable support leg with a two-way hydraulic lock.
(The leg operation is manual and can be controlled separately) with a 0.5 ton hook.
Main features:
1. The boom and support legs are both made of low alloy Q345 profiles, with no welds around them. They have a beautiful appearance, high stress, and high strength;
2. The H-shaped leg has good stability and can be operated simultaneously or independently. It is flexible to operate and can adapt to various working conditions;
3. The rotary mechanism adopts an adjustable type for easy adjustment;
4. The turntable rotates 360 ° in both directions and adopts advanced worm gear reduction mechanism (with self-lubricating and self-locking functions), which can be easily maintained in the later stage by adjusting the bolt position to achieve the desired effect;
5. The boarding operation adopts an integrated electronic control valve block mode, with a beautiful layout, smooth operation, and convenient maintenance;
6. Get off and get on interlocking, safe and reliable operation;
7. The boarding operation is achieved through a throttle valve to achieve infinite speed regulation;
8. The hanging basket adopts an external pull rod mechanical leveling, which is more stable and reliable;
9. The turntable and hanging basket are equipped with start and stop switches, which are easy to operate and save fuel;
For the 13 meter high-altitude work vehicle, we refer to the following standards:
The supplier shall use the latest national and industry standards issued and implemented, and may use other standards with the consent of the user
Can achieve higher standards. According to industry standards, provisions have been made for product quality, and the performance of the products provided by the supplier should meet national standards. When there is a deviation between the clauses in the above standards and these technical conditions, these technical conditions shall prevail.
The following standards are cited:
1) GB/T9465 Aerial Work Vehicles
GB3766 General Technical Conditions for Hydraulic Systems
2) GB7258 Technical Conditions for Safety of Motor Vehicle Operation
3) GB1589 "Load and Mass Limits for External Dimensions of Vehicles"
4) GB4785 Installation Regulations for External Lighting and Light Signal Devices of Motor Vehicles and Trailers
5) GB11567.1.2 "Requirements for side and rear lower protection of automobiles and trailers"
6) QC/T252 "Specification for Type Approval Testing of Special Purpose Vehicles"
7) JB/ZQ3011 General Technical Conditions for Welding of Construction Machinery
8) JG5099 Safety Rules for High Altitude Work Machinery
9) CCAP-C11-01-2014 Implementation Rules for Compulsory Product Certification for Automobiles
3. Environmental conditions for use
1) Altitude: ≤ 1000 meters
2) Environmental temperature: -5 ℃~+40 ℃
3) Relative humidity: ≤ 95% (25 ℃)
4) Seismic resistance: Ground horizontal acceleration of 0.3g
Ground vertical acceleration of 0.15g acting simultaneously for three consecutive sine waves with a safety factor of 1.67
5) Maximum daily temperature difference: 15 ℃
6) Sunlight intensity (at wind speed of 0.5m/s): 0.1W/cm2 7) Maximum wind speed: ≤ 10.7m/s1
4. Main technical parameters Basic upper garment configuration Set
Arm form: Three section folding arm
Material profile Q345B/4mm
Arm cross section quadrilateral
Fluctuation angle 0 ° -70 ° (relative to the horizontal plane)
The maximum working height of the working condition is 13m
At maximum operating height
Assignment amplitude of 3m
Maximum homework amplitude of 6.2m
At maximum homework amplitude
The homework height is 8.6m
Double directional 360 ° continuous rotation
The maximum lifting weight of the lifting arm is 1000Kg
The maximum lifting height is 6.8m
Hook 1T
Support legs, front and rear H-shaped
Support leg material profile Q345B/5mm
Leg span longitudinal (mm): 3240, transverse (mm): 3180
The four legs of the hydraulic lock are equipped with bidirectional hydraulic locks
Rear leg strobe light yellow; Two
The carriage is made of high-quality carbon steel and profiles, covered with 3mm anti slip patterned steel plates
Toolbox 1200 * 400 * 500; Mold stamped door with stainless steel door lock
Fence Φ 20 stainless steel pipes
Step up and down steps on the side of the driver's cab
High quality carbon steel cold-formed profiles for side and rear protection; High strength